elektrobot.hu elektrobot.hu
\ Loading news...
/
Új vagy? Klikk! Tudtad-e? GYIK Miért mi?
Menü
  
Kijelző, átalakító, mikroproc...  »  Fejlesztő modulok, Arduino, Raspberry  » 
Raspberry Pi Pico rp2040 development board with 0.42 inch LCD supports Arduino and micropyth
Cikkszám: #7562
Cikkszám: #7562
(Bruttó) Ár:  10,990 Ft
(Bruttó) Ár: 10,990 Ft
Beszállítás alatt Beszállítás alatt
db Kosárba tesz Kosárba tesz
Raspberry Pi Pico rp2040 development board with 0.42 inch LCD supports Arduino and micropyth
Raspberry Pi Pico rp2040 development board with 0.42 inch LCD supports Arduino and micropyth
Raspberry Pi Pico rp2040 development board with 0.42 inch LCD supports Arduino and micropyth
Raspberry Pi Pico rp2040 development board with 0.42 inch LCD supports Arduino and micropyth
Raspberry Pi Pico rp2040 development board with 0.42 inch LCD supports Arduino and micropyth
Raspberry Pi Pico rp2040 development board with 0.42 inch LCD supports Arduino and micropyth

RP2040-0.42LCD

RP2040-0.42LCD is a high-performance Development board ,Integrated 0.42 "LCD (70×40 resolution).with flexible digital interfaces. It incorporates Raspberry Pi's RP2040 microcontroller chip.The RP2040 features a dual-core Arm Cortex-M0+ processor clocked at 133MHz with 264KB internal SRAM and 2MB internal flash storage.


Inside the RP2040 is a 'permanent ROM' USB UF2 bootloader. What that means is when you want to program new firmware, you can hold down the BOOTSEL button while plugging it into USB (or pulling down the RUN/Reset pin to ground) and it will appear as a USB disk drive you can drag the firmware onto.

There is great C/C++ support, unofficial (but really good) Arduino support, You can also use micropthon and circuitpython.


Features

RP2040 32-bit Cortex M0+ dual core running at ~125 MHz @ 3.3V logic and power

264 KB RAM

2 MB SPI FLASH chip for storing files and CircuitPython/MicroPython code storage. No EEPROM

Four 12 bit ADCs (one more than Pico)

Two I2C, Two SPI and two UART peripherals

Integrated 0.42 "LCD

Both Reset button and Bootloader select button for quick restarts (no unplugging-replugging to relaunch code)

1x RGB(GPIO2)

3.3V power indicator LED

3.3V regulator with 500mA peak current output

USB Type C connector lets you access built-in ROM USB bootloader and serial port debugging


Size & Weight


Size: 23.5 x 18 mm
Weight: 
2.5g

DOCUMENTS

https://github.com/01Space/RP2040-0.42LCD



Kapcsolódó termékek


Kapcsolódó cikkek

Vélemények (küldje be Ön is véleményét)



Figyelem, a képek csak illusztrációk, a kiegészítők, a színek és a csomagolás eltérhet.
A termékleírásban esetlegesen előforduló hibákért felelősséget nem vállalunk. Ha a paraméterekben nem biztos, ellenőrizze a gyártónál.
RÓLUNK
Cégünk elektronikai és szoftveres fejlesztésekkel foglalkozik, ami mellett internetes kereskedelmet is indítottunk az ehhez kapcsolódó modulok és fejlesztő egységekkel. Már több mint 15.000 féle termék rendelhető, melyből több mint 5000 saját raktárunkról azonnal elérhető. Fiatal cégként dinamikusan bővülünk, alkalmazkodunk a modern igényekhez. Támogatjuk a hazai fejlesztéseket, és diákokat, termékekkel, szolgáltatásokkal, és saját tudásunkkal. Rendszeres vásárlóink között tudhatunk rengeteg magyar nagyvállalatot, oktatási intézményt, megbízóink között pedig több fejlődő kis- és közép- vállalkozást.
KÖZÖSSÉGI JELENLÉT
2016-tól mi béreljük az elektrobot.hu-t, mely egy közösségi blog és híroldalként indult, ezen keresztül korábban több elektronikai cég forgalmazott, és jelenleg is hírdeti szolgáltatásait. Rendszeresen jelen vagyunk a magyar elektronikai fórumokon online és kiállítások, rendezvények formájában. Próbáljuk összehozni az oktatásban és versenyeken résztvevőket a fiatal cégekkel, és a komolyabb megbízókkal.
...